форум Радиолюбительского ДВ портала > Технический раздел

QRSS Keyer и частные вопросы синтезаторостроения. Arduino. Rapsberry pi.

<< < (6/15) > >>

rw3adb:


> QRSS-30 will be possible?

Of course!
We are building the CW/QRSS/DFCW keyer with Arduino.

And the exiter should be QRG oven stabilized, long term drift about 2*10^-8
The 475 kHz generator should be a PLL synthetizer with an external BCD coded
connector programming frequency.
http://www.k7jrl.com/pub/manuals/adret/cs201/

73 de Claudio IK2PII

rw3adb:
до кучи, на тему.

http://www.hanssummers.com/ultimate3.html

rw3adb:
мда, 3.5 года прошло до начала попыток использования сего:

LF: TXing WSPR on 630m on a Raspberry Pi, Stefan in QRPPPP...

Hi MF,

Today i've got i 3rd Raspberry Pi. I quickly installed the WSPR softaware and since a few minutes i am transmitting WSPR-2 on 630m, my usual frequency 475.685 kHz.

I'm directly using the GPIO output pin, without an amp stage behind! The rectangular 3.3V output voltage is passing a cap and an isolation transformer (FT50-77) as well as a simple pi-filter, because it is a Raspberry pi! ;-)

See: https://dl.dropboxusercontent.com/u/19882028/MF/Raspberry%20Pi%20B%2B%20WSPR%20TX.jpg

I measured an output power of about 10 mW at 50 Ohm. It is now connected to my MF antenna and transmits in a 100% duty cycle. I still have to learn how to reduce it but this will not take long.

With 10 mW TX power i managed decodes by 3 stations now.

3 spots:
Timestamp    Call    MHz    SNR    Drift    Grid    Pwr    Reporter    RGrid    km    az
 2015-03-18 20:32      DK7FC      0.475684      -21      0      JN49ik      0.01      DH5RAE      JN68qv      345      98
 2015-03-18 20:12      DK7FC      0.475685      -24      0      JN49ik      0.01      F1AFJ      JN06ht      667      247
 2015-03-18 20:06      DK7FC      0.475683      -27      0      JN49ik      0.01      DL1DBC      JO41bi      217      349


Does someone have good ears to get a decode from me? :-) It is a challenge! :-)

73, Stefan/DK7FC

PS: The signal is so weak that my RX antenna frontend is not overloaded, so at that power level i can transmit and receive to the same time :-)
PPS: A small amp stage will follow soon, i intend to use an BS170 running at 5 V.

rw3adb:
да, на всякий случай, малоль кто-то не в курсе.
выпустили, оказывается, такую приблуду к малине:

http://www.suptronics.com/Xseries/x300.html

нормальная звуковуха на борту... ну-с, сеньоры линуксоиды, ау!

rw3adb:
случайно набрёл, может кому из наших будет полезно.

Навигация

[0] Главная страница сообщений

[#] Следующая страница

[*] Предыдущая страница

Перейти к полной версии